
Application instructions
**IMPORTANT INFORMATION**
When you receive your decals please store sealed inside at room temperature away sunlight & sources of heat and cold.
The application tape that holds the decal together is low tack and temporary and can lift off slightly from the actual vinyl exposed.
If you are not fitting within 3-4 weeks please contact us to pause your order to avoid any issues.
Many thanks.
Here’s a short video to give you an overview of fitting.
Please READ preparation and care steps below (under video).
To ensure that your decals last for as long as possible on your vehicle please read and follow instructions carefully:
Inspect decals straight away when received to ensure no damage from delivery.
Introduction
Important. If not being fitted straight away please only store in the tube away from heat and sunlight. Do not store unrolled.
When ready to fit. LAY THE DECAL OUT ON A FLAT SMOOTH SURFACE AND GENTLY RUB THE APPLICATION TAPE ONTO THE DECAL – (the application tape is very low tack to help application – it naturally starts to lift off – it will be binned at the end of the process but needs to be stuck to the decal for fitting
1. Offer up and Check Size before fitting.
2. In winter, fit at least above 7 degrees C. If tempurature is lower a hairdryer will be needed to warm the decal to release the adhesive.
2.1 In summer, fit during the cool part of the day (Please ensure the body panel is cool and out of direct sunshine especially during a heatwave).
3. DO NOT fit in direct sunlight heat on a hot day – the vinyl could strech and the glue will be too soft to harden.
4. AVOID WASHING WITH A JETWASH OR CAR WASH BRUSHES.
5. Do not PREWASH WITH A VEHICLE SHAMPOO that contains wax.
6. After washing CLEAN BODYWORK WITH A NON AMMONIA CLEANER.
6. After washing CLEAN BODYWORK WITH A NON AMMONIA CLEANER.
7. Avoid wrapping around acrhes to ensure long life.
8. Indent when Trimming by 1mm or 2mm – It looks factory and looks professional!
9. Make sure that the bubbles are wiped out during inital contact with body work and immediatly after the application tape is removed (The glue cures and hardens within 20-30 minutes).
10. When removing bubbles, gently tease them toward the edge of the decal.
11. Make sure you have a nice cup of tea, read the below instructions carefully and do not rush!
12. PLEASE NOTE: If the application tape is not picking up the vinyl, especially with detailed designs, please ensure you are removing the backing paper from the application tape. Not the carrier tape from the backing paper.
Seems a minor point but the manufacturer recommends this to aid the process. Also a warm (not hot) hairdryer on the backing paper will help soften the adhesive to release.
Step One

Any lifting of the edge of the decal can cause the decal to lift off the surface of your vehicle which will cause peeling.
1. It is recommended you install your vinyl decal in a garage or building. 2. Room and installation surface temperature is recommended to be between 10°C (50°F) and 20°C (68°F) to reduce stretching or other un-desired effects. 3. Do not store your vinyl decal in direct sunlight.
Materials Needed
– Installation squeegee (a credit card will do!)
– Masking tape
– Glass cleaner (non AMMONIA BASED)
– Paper towel
– Measuring tape or ruler.
– Scissors or Razor
Preparation
Remove all dirt, grease and/or wax from the surface before you install your vinyl decal. This includes wax from car washes, turtle wax, rain-x, compound, etc. Your new vinyl decal will NOT adhere properly if you do not have a clean installation surface.
Caution! Do not use ammonia based cleaner. It will out gas for a couple of weeks and create bubbles under your vinyl decal.
If you do not feel confident to fit your new Beatnik decal any local body shop will do it for you.
Step Two
Inspect your new vinyl decal for any shipping damages – please do not fit decals that you think have an issue.
In this case please contact us straight away- we are here to help!
Using a squeegee on a table, press firmly over the whole decal assuring the pre-mask (transparent application tape) is properly stuck to the vinyl decal.
Once finished, place your decal on the surface (application tape up and backing paper down).

Step Three

Place pieces of masking tape on top of the decal “pre-mask application tape” and surface to hold the decal in place.
If needed, measure with a ruler or measuring tape to make sure your decal is properly lined up.
Once in place, put a long piece of tape across the decal in the center as shown below. Remove the masking tape from one side of the decal and vehicle surface creating a hinged ‘flap’.
Step Four
Raise the hinged ‘flap’, and begin to peel the backing “liner” off the decal (Not the Application tape), exposing the adhesive side of the decal. Only peel the “liner” from the decal until you reach the masking tape that crosses the whole decal.
DO NOT ALLOW THE STICKY PART OF THE DECAL TO TOUCH THE SURFACE YOU ARE APPLYING TO.
Using scissors or a razor, cut away the peeled “liner” close to the long piece of masking tape that crosses the decal. Do not allow the scissors or razor to touch the decal as it may stick accidentally peeling the decal off the “pre-mask”.
If this does not make sense view quick guide video above
PLEASE NOTE: To reiterate, if the application tape is not picking up the vinyl, especially with detailed designs, please ensure you are removing the backing paper from the application tape. Not the carrier tape from the backing paper. Seems a minor point but the manufacturer recommends this to aid the process. Also a warm (not hot) hairdryer on the backing paper will help soften the adhesive to release.

Step Five

Using your squeegee and starting in the middle where your masking tape crosses the decal, begin to apply the sticky side of the decal to the surface.
Use horizontal strokes to apply the decal equally. Continue smoothing out the decal from top to bottom with long horizontal strokes assuring the decal is securely adhered to the surface.
N.B If the application tape will not lift the decal vinyl try removing the back paper from the vinyl. This is a recommendation form the manufacturer.
Step Six
Place a long piece of masking tape parallel to the current piece of masking tape that crosses the decal on the decal side that you just adhered to the surface.
Then remove the original long piece of masking tape that crossed the decal. This will secure the decal so you can peel off the final piece of “liner”. Also remove the small corner pieces of masking tape.
Slowly peel the final piece of “liner” off exposing the adhesive side of the decal. Once again do not allow the sticky part of the decal to touch the surface.

Step Seven

Using your squeegee and starting in the middle where your masking tape crosses the decal, begin to apply the final sticky side of the decal to the surface.
Use horizontal strokes to apply the decal equally. Continue smoothing out the decal from top to bottom with long horizontal strokes assuring the decal is securely adhered to the surface.
Step eight
Once completed leave your decal for 15mins, go make yourself a nice cup of tea.
Once you’ve come back to it you can simply peel off the application tape and stand back to admire your handy work.
Please note when trimming to gaps in the door panel it works really nicely to trim 1-2mm before the end of the panel – looks PRO and will make you deals last longer.
We hope you are as happy with your beatnik decal as we were designing them for you.

ABOUT MENU
Your basket
Recently viewed
-
Hibiscus Bonnet!
£30.83 – £40.83Price range: £30.83 through £40.83
Reviews

LOVE these products. Ive bought cheaper (slightly) in the past but your products obliterate them. Thank you!

Absolutely brilliant very happy the way the design turned out kept in contact with me all the way through the order very pleased thank you

Fantastic service. Had a query but confirmed within a couple of hours. Looking forward to receiving these stickers.

Exceptional order, with fast P&P and quick responses to enquiry. Great products. Would use again.

I wanted a pretty unusual design.. and Daniel did an amazing job. He also sorted out a minor issue quickly and professionally. I’m very impressed with the end result and would recommend Beatnik without any hesitation.

Without doubt the best decal company that I ever used. Superb quality products and great customer service every time.

Great quality rear quality decal set, I went matte black inverse print on black glass to give a stealth look, really impressed with result and great support from Daniel and his recommendation, spot on!

Nothing was too much of a problem…. Very pleased with the final design. I would highly recommend Beatnik. Thank you guys!!!

Excellent decal and communication. I had a superb decal custom made for my husbands VW Campervan – he loves it! Thank you!!
Highly recommended.

Super customer service from this company. Swift reply to emails and Daniel, who dealt with all of it, went above and beyond to help as well as get our order to us on time before our travels. Will highly recommend.

